Power factor correction calculator: kVAR, amps and µF

Enter the load in kW, its power factor now and the power factor you want. Get the capacitor kVAR, the kVA and line current before and after, the percent current cut and the capacitance in microfarads, single-phase or three-phase, at 60 or 50 Hz. Every step is shown.

Load and target

Present angle = acos 0.7; tan of it
45.57°; 1.0202
Target angle = acos 0.95; tan of it
18.19°; 0.3287
Load kVAR now = 100 kW × 1.0202
102.02 kVAR
Load kVAR at target = 100 kW × 0.3287
32.87 kVAR
Capacitor kVAR = kW × (tan φ1 − tan φ2) = 102.02 − 32.87
69.15 kVAR
kVA = kW ÷ PF
142.9 kVA before, 105.3 kVA after
Line current = kW × 1,000 ÷ (1.732 × 480 V × PF)
171.8 A before, 126.6 A after
Current cut = 1 − 0.7 ÷ 0.95
26.3%
Delta bank: each capacitor supplies 69.15 ÷ 3 = 23.05 kVAR at 480 V; C = Q ÷ (2π × 60 Hz × V²)
265.4 µF per phase

Enter the load's real power in kW and its power factor as a decimal. Three-phase uses the line-to-line voltage, and the capacitance is for a delta-connected bank, one capacitor across each pair of lines.

Free 10-question check

Studying for TX Journeyman? Take the free 10-question check to see exactly which topics to fix first, then close the gaps with the Bonding Jumper course.

Free TX Journeyman check

Or read a full free lesson first (no signup).

Studying with a coworker? Send them the free check.

The formulas

Power factor is true power over apparent power, and it is the cosine of the angle φ between voltage and current. The three powers form a right triangle: kW along the base, kVAR up the side and kVA on the slope. A capacitor in parallel with the load supplies reactive power that cancels part of the load's, which shortens the kVAR side and with it the kVA, while the kW stays the same.

  • Capacitor kVAR = kW × (tan φ1 − tan φ2), where φ1 = acos(present PF) and φ2 = acos(target PF).
  • kVA = kW ÷ PF.
  • Line current, single-phase: I = kW × 1,000 ÷ (V × PF). Three-phase: I = kW × 1,000 ÷ (1.732 × V × PF), with V line to line.
  • Current cut = 1 − PF1 ÷ PF2. The same kW at a higher power factor needs less current.
  • Capacitance: C = Q ÷ (2π f V²), with Q in VAR across the capacitor. A delta bank puts one capacitor across each pair of lines, so each takes Q ÷ 3 at the line voltage.

Worked example 1: 100 kW three-phase, 0.70 to 0.95

480 V, 60 Hz. tan(acos 0.70) = 1.0202 and tan(acos 0.95) = 0.3287. Capacitor kVAR = 100 × (1.0202 − 0.3287) = 69.15 kVAR. kVA falls from 100 ÷ 0.70 = 142.9 to 100 ÷ 0.95 = 105.3. Current falls from 100,000 ÷ (1.732 × 480 × 0.70) = 171.8 A to 100,000 ÷ (1.732 × 480 × 0.95) = 126.6 A, a 26.3% cut. Each capacitor of a delta bank supplies 69.15 ÷ 3 = 23.05 kVAR at 480 V, so C = 23,051 ÷ (2π × 60 × 480²) = 265.4 µF per phase.

Worked example 2: 8 kW single-phase, 0.8 to 1.0

240 V, 60 Hz. tan(acos 0.8) = 0.75 and tan(acos 1.0) = 0, so the capacitor supplies 8 × 0.75 = 6.0 kVAR. kVA falls from 10 to 8 and current from 41.7 A to 33.3 A, a 20% cut. C = 6,000 ÷ (2π × 60 × 240²) = 276.3 µF. This is the load from the power factor guide, worked the other way.

These are original arithmetic examples, not exam questions.

Where it fits

The apparent vs true power guide sets out the power triangle these steps stand on. For the power formulas on their own, single-phase and three-phase, use the Ohm's law calculator, and for kVA to amps on each side of a transformer, the transformer calculator.

What this calculator leaves out

  • Wye-connected banks: each capacitor sits at the line voltage ÷ 1.732, so it needs three times the delta value in µF for the same kVAR.
  • Standard bank sizes: round to a rating the maker offers at your system voltage.
  • Harmonics, switched or automatic banks, and capacitors placed at individual motors.
  • Conductor and overcurrent sizing for the bank, which come from the NEC.

Power factor correction questions

What is kVAR in power factor correction?

kVAR is kilovolt-amperes reactive, the power that flows back and forth between the source and an inductive load each cycle without doing work. A load's kVAR is its kW times tan(acos PF). A capacitor supplies kVAR of the opposite sign, so the capacitor kVAR you need is kW × (tan φ1 − tan φ2). For 100 kW at 0.70 that is 102.02 kVAR now and 32.87 kVAR at 0.95, so the capacitor supplies 69.15 kVAR.

Why does correcting power factor cut the current?

The load still uses the same kW, but at a higher power factor it needs fewer kVA to get it, and the current follows the kVA. Current falls in the ratio PF1 ÷ PF2. Going from 0.70 to 0.95 cuts it by 1 − 0.70 ÷ 0.95 = 26.3%: on a 100 kW, 480 V three-phase load, from 171.8 A to 126.6 A. The capacitor supplies the reactive current locally, so it no longer travels back to the source.

How do I size a power factor correction capacitor in µF?

Use C = Q ÷ (2π f V²), with Q in VAR and V in volts across the capacitor. On single-phase, Q is the whole kVAR. A three-phase delta bank has one capacitor across each pair of lines, so each takes one third of the kVAR at the line voltage. For 69.15 kVAR at 480 V and 60 Hz: 23,051 VAR ÷ (2π × 60 × 480²) = 265.4 µF per phase.

Why aim for 0.95 and not 1.0?

It is a design choice, not a code rule. The last step costs the most: taking 100 kW from 0.95 to 1.0 needs another 32.87 kVAR, about 48% more capacitor than the 69.15 kVAR that got it to 0.95, for 6.3 A less current at 480 V. A fixed bank sized for 1.0 at full load also overshoots when the load drops, because the capacitor keeps supplying the same kVAR while the motors need less, and the circuit turns capacitive. Stopping short of 1.0 takes most of the current cut and leaves margin against that.

Works the power triangle: capacitor kVAR = kW × (tan(acos PF1) − tan(acos PF2)), kVA = kW ÷ PF, and line current = kW × 1,000 ÷ (V × PF), with 1.732 in the divisor for three-phase. Capacitance is C = Q ÷ (2π f V²), per phase for a delta bank. A study and sizing aid; the capacitor maker's data and the NEC decide the installed bank.

Try one free question

Try one question

Question 1 of the free 10-question check on TX Journeyman. No signup. Then ask Lug, the AI study assistant, why the answer is right and the others are wrong.

Question 1 of 10 · free checkUntimed

Special Occupancies, Equipment, and Conditions

After normal power fails, within how many seconds must an emergency system make power available to its required loads?

Press A-D or 1-4 to choose an answer while this question is on screen.

Choose an answer to begin

Email me the TX Journeyman study plan

A week-by-week plan from today to your exam, weighted to the published exam outline. It shows here at once and a copy comes by email.

Ask Lug before you buy AI your AI study assistant

See what's on the TX Journeyman exam, test yourself with 5 quick questions, or find the plan that fits you.

Sources

The formulas on this page are standard AC circuit math, explained in our own words, and need no code book.

  • Tony R. Kuphaldt, Lessons in Electric Circuits, Vol. II, chapter 11 (All About Circuits textbook). Calculating Power Factor. Checked 21 Nov 2026.
    https://www.allaboutcircuits.com/textbook/alternating-current/chpt-11/calculating-power-factor/
  • Tony R. Kuphaldt, Lessons in Electric Circuits, Vol. II, chapter 11 (All About Circuits textbook). Practical Power Factor Correction. Checked 21 Nov 2026.
    https://www.allaboutcircuits.com/textbook/alternating-current/chpt-11/practical-power-factor-correction/

Preparing for the Texas journeyman exam?

You just worked a power triangle from kW to kVAR, amps and microfarads. Power factor runs through the motor and load calculations, and the free 10-question check scores you across the exam's subject areas, needs no signup and explains every answer. The Bonding Jumper course then drills your weak spots.

Free 10-question check

The TX Journeyman course

Available now · instant access

The TX Journeyman course

  • 10modules of lessonsEvery task on the outline
  • 3timed practice exams80 scored questions, 240 minutes; exam day adds 5 unscored
  • 442practice questionsEach one explained
  • 1week-by-week study planSet to your exam date

Turn a practice answer into a study step. In untimed practice, ask Lug AI about any question you answer, follow up, then see your weakest topics and what to drill next.

Texas Journeyman course$99

Terms and refunds · Secure checkout by Stripe · Billed by Nori Software

See the course

Compare plans

Every answer comes with a full explanation.

By the Bonding Jumper editorial team. Report an error.

Add this power factor correction calculator to your site

Copy this HTML with its attribution link. The frame scrolls to include the calculator and explanations; no external script is needed.