Conduit bending calculator: offsets, saddles and 90s

Pick the bend, enter the rise or obstruction height, and get the distance between marks, the shrink and the degrees used, in inches or millimeters. It covers offsets at any angle, 3-point and 4-point saddles and 90° stubs, and keeps a running total of degrees against the 360° limit between pull points. Every step is shown.

Bend type and sizes

Multiplier = 1 ÷ sin 30° (the cosecant)
2.000
Distance between bends = rise × multiplier
12 in (about 12 in)
Shrink per inch of rise = tan(15°)
0.268 in per inch
Shrink = rise × shrink per inch
1.61 in (about 1 5/8 in)
Degrees used = 2 × 30°
60°

The math treats each bend as a sharp corner. The rise is how far the run must move over; the height is how far it must clear. Distances are measured from the conduit end; leave them blank to see spacing and shrink only. For a 90° stub, type the take-up printed on your bender for the conduit size you are bending.

Degrees between pull points

Bends in the run
6
Total
240° of 360°
Within the 360° limit, with 120° left before the next pull point.

Free 10-question check

Studying for TX Journeyman? Take the free 10-question check to see exactly which topics to fix first, then close the gaps with the Bonding Jumper course.

Free TX Journeyman check

Or read a full free lesson first (no signup).

Studying with a coworker? Send them the free check.

Conduit offset multiplier and shrink table

The multiplier is 1 ÷ sin θ and the shrink per inch is tan(θ ÷ 2), worked to three decimals. Multiply either by the offset rise in inches, or in millimeters, since both are ratios.

Bend angleMultiplier (cosecant)Shrink per inch of riseDegrees per offset
10°5.7590.08720°
15°3.8640.13230°
22.5°2.6130.19945°
30°2.0000.26860°
45°1.4140.41490°
60°1.1550.577120°

How the offset math works

An offset is two equal bends that move the run over by a set rise. Between the bends the conduit is the long side of a right triangle whose short side is the rise, so its length is the rise ÷ sin θ. That length is the distance between your marks.

  • Distance between bends = rise × cosecant θ. The cosecant is the multiplier.
  • Shrink = rise × tan(θ ÷ 2). The angled piece covers rise ÷ tan θ along the run but uses rise ÷ sin θ of conduit; the difference is the shrink.
  • Degrees used = 2 × θ. Two bends at the same angle.

Worked example: a 6 in offset at 30°. Distance between bends = 6 × 2.000 = 12 in. Shrink = 6 × 0.268 = 1.61 in, about 1 5/8 in. If the offset must be complete 36 in from the conduit end, mark 2 goes at 36 + 1.61 = 37.61 in and mark 1 at 37.61 − 12 = 25.61 in. The offset uses 60° of the run's 360°.

3-point saddle: 2.5 or 2.613?

A 3-point saddle crosses a pipe or other obstruction with a 45° center bend and two 22.5° outer bends. Each half is a 22.5° offset, so the outer marks sit height ÷ sin 22.5° = 2.613 × height from the center mark, and the center mark moves 0.199 × height past the measured center, which is tan 11.25°.

Klein Tools' saddle table rounds these to 2-1/2 in and 3/16 in per inch of height. For a 4 in obstruction the exact spacing is 10.45 in against 10 in from the rounded figure, and the center mark moves 0.80 in against 3/4 in. The tool shows both so you can see what the rounding costs on a tall saddle. The saddle uses 90° of the 360°, and its total shrink is 2 × 0.199 × height.

4-point saddle

A 4-point saddle is two offsets of the same rise with the obstruction's width between them. Bends 1 and 2 form the first offset, bends 3 and 4 the second, and the straight run between bends 2 and 3 equals the width. A 4 in by 8 in obstruction at 30° puts each pair of bends 8 in apart with 1.07 in of shrink per offset, 2.14 in in total, and uses 120°.

90° stubs and take-up

For a stub, subtract the take-up from the stub height you want and mark the conduit that far from the end. Take-up depends on the bender and the conduit size, and Klein Tools, for one, marks it on each of its bender heads (Conduit Bender Guide). Type the figure from your own bender: for a 12 in stub on a bender marked with a take-up of T, the mark goes 12 − T in from the end.

The 360-degree rule between pull points

The 2014 NEC caps the bends in a run between pull points, such as boxes and conduit bodies, at 360° in total, the same as four 90° bends. Each raceway article carries the rule in its own section: 358.26 for EMT, 344.26 for rigid metal conduit, 342.26 for IMC and 352.26 for PVC. These are 2014 edition section numbers only, from the copy Public.Resource.Org posts; look the rule up in the edition your job is under. Every offset, saddle and kick counts, so a run with a 90° stub, a 30° offset and a 3-point saddle has already used 240°. Use the run total under the calculator to add them up as you lay out the job.

The bending rules sit in the Chapter 3 raceway articles. The raceway guide covers which wiring methods count as raceways, and the conduit fill guide sizes one from the Chapter 9 tables.

What this calculator leaves out

  • Bend radius and gain: it treats offset and saddle bends as sharp corners and does not work the gain for back-to-back 90s.
  • Springback and overbending: the angle is the one the conduit rests at after the bend.
  • Kicks, back-to-back bends, rolling offsets and segment bending of large conduit.

Conduit bending questions

What is the offset multiplier for conduit bending?

It is the cosecant of the bend angle, 1 ÷ sin θ. Multiply the offset rise by it to get the distance between the two bend marks. To three decimals, 10° is 5.759, 22.5° is 2.613, 30° is 2.000, 45° is 1.414 and 60° is 1.155. A 6 in offset at 30° puts the marks 6 × 2 = 12 in apart.

What is shrink in a conduit offset?

Shrink is the run an offset uses up: once bent, the conduit reaches less far along the run than it did straight. Per inch of rise it equals tan(θ ÷ 2), which is 0.087 at 10°, 0.199 at 22.5°, 0.268 at 30°, 0.414 at 45° and 0.577 at 60°. A 6 in offset at 30° shrinks 6 × 0.268 = 1.61 in, so add that to your measurement to the obstruction before you mark.

Why is 30 degrees the easy offset angle?

Because sin 30° is exactly 0.5, the multiplier is exactly 2: the distance between bends is twice the rise, which you can work in your head. Shrink is 0.268 in per inch, close to 1/4 in, and the offset uses 60° of the 360° allowed between pull points. Steeper angles fit tighter spaces but use more of the 360°; shallower angles use fewer degrees but need a longer run between bends.

How many degrees of bends are allowed between pull points?

The 2014 NEC allows 360° in total, the same as four 90° bends, between pull points such as boxes and conduit bodies. Each raceway article sets the limit in its own section, cited here from the 2014 edition only: 358.26 for EMT, 344.26 for rigid metal conduit, 342.26 for IMC and 352.26 for PVC. Look the rule up in the edition your job is under. Count every bend: a 30° offset is 60°, a 3-point saddle with a 45° center is 90° and a 4-point saddle at 30° is 120°.

Works each bend as a sharp corner: distance between bends = rise ÷ sin θ, shrink = rise × tan(θ ÷ 2), and a 3-point saddle as two 22.5° halves around a 45° center. The 90° stub subtracts the take-up you enter from your bender, and the run total adds every bend against the 360° limit between pull points. A layout and study aid; your bender's marks and the NEC edition your job is under decide the final bend.

Try one free question

Try one question

Question 1 of the free 10-question check on TX Journeyman. No signup. Then ask Lug, the AI study assistant, why the answer is right and the others are wrong.

Question 1 of 10 · free checkUntimed

Special Occupancies, Equipment, and Conditions

After normal power fails, within how many seconds must an emergency system make power available to its required loads?

Press A-D or 1-4 to choose an answer while this question is on screen.

Choose an answer to begin

Email me the TX Journeyman study plan

A week-by-week plan from today to your exam, weighted to the published exam outline. It shows here at once and a copy comes by email.

Ask Lug before you buy AI your AI study assistant

See what's on the TX Journeyman exam, test yourself with 5 quick questions, or find the plan that fits you.

Sources

Preparing for the Texas journeyman exam?

You just laid out offsets, saddles and stubs and checked the run against the 360° limit. The free 10-question check scores you across the exam's subject areas in minutes, needs no signup and explains every answer. The Bonding Jumper course then drills your weak spots.

Free 10-question check

The TX Journeyman course

Available now · instant access

The TX Journeyman course

  • 10modules of lessonsEvery task on the outline
  • 3timed practice exams80 scored questions, 240 minutes; exam day adds 5 unscored
  • 442practice questionsEach one explained
  • 1week-by-week study planSet to your exam date

Turn a practice answer into a study step. In untimed practice, ask Lug AI about any question you answer, follow up, then see your weakest topics and what to drill next.

Texas Journeyman course$99

Terms and refunds · Secure checkout by Stripe · Billed by Nori Software

See the course

Compare plans

Every answer comes with a full explanation.

By the Bonding Jumper editorial team. Report an error.

Add this conduit bending calculator to your site

Copy this HTML with its attribution link. The frame scrolls to include the calculator and explanations; no external script is needed.