Conduit Offset Multiplier Chart and Shrink
The conduit offset multiplier is the cosecant of the bend angle, 1 ÷ sin θ, so it is 2 at 30° and 1.414 at 45°. Multiply the offset depth by it to get the distance between your two bend marks. Shrink, the length of run the offset uses up, is tan(θ ÷ 2) per inch of offset, which is 0.268 in at 30°. The chart below works both out for 10°, 15°, 22.5°, 30°, 45° and 60°, then puts them to work on two offsets and a 3-point saddle.
Conduit offset multiplier chart
| Bend angle | Multiplier (1 ÷ sin θ) | Shrink per inch, exact (tan θ/2) | Shrink per inch, nearest 1/16 in | Degrees per offset |
|---|---|---|---|---|
| 10° | 5.759 | 0.087 | 1/16 in | 20° |
| 15° | 3.864 | 0.132 | 1/8 in | 30° |
| 22.5° | 2.613 | 0.199 | 3/16 in | 45° |
| 30° | 2.000 | 0.268 | 1/4 in | 60° |
| 45° | 1.414 | 0.414 | 7/16 in | 90° |
| 60° | 1.155 | 0.577 | 9/16 in | 120° |
Each figure is worked to three decimals. An offset is two bends at the same angle, so the degrees column is 2 × θ. The multiplier and the exact shrink are ratios, so they work in millimeters too: a 150 mm offset at 30° puts the marks 300 mm apart.
How the two formulas work
Between the two bends the conduit is the long side of a right triangle whose short side is the offset depth. That long side is depth ÷ sin θ, which is why the multiplier is the cosecant. Along the run, the same piece covers only depth ÷ tan θ. The difference between the two is the shrink, and it simplifies to depth × tan(θ ÷ 2).
The shallower the angle, the bigger the multiplier and the smaller the shrink. A 10° offset stretches over almost six times its depth but barely shortens the run. A 60° offset fits a tight space but uses 120° of the 360° you are allowed between pull points.
Field charts round these numbers
Klein Tools' Conduit Bender Guide prints an offset table with rounded figures. It has no 15° row.
| Bend angle | Klein multiplier | Exact | Klein shrink per inch | Exact |
|---|---|---|---|---|
| 10° | 6 | 5.759 | 1/16 in | 0.087 |
| 22.5° | 2.6 | 2.613 | 3/16 in | 0.199 |
| 30° | 2.0 | 2.000 | 1/4 in | 0.268 |
| 45° | 1.4 | 1.414 | 3/8 in | 0.414 |
| 60° | 1.2 | 1.155 | 1/2 in | 0.577 |
The exact figures treat each bend as a sharp corner, the same way our calculator does. The gap grows with the offset depth: a 10 in offset at 45° puts the marks 14.14 in apart exact and 14 in from the rounded 1.4, and at 10° the rounded 6 adds about 1/4 in for every inch of offset. Check your first few offsets against your own bender's marks.
Try one question
Question 1 of the free 10-question check on TX Journeyman. No signup. About 14 minutes. Most checks include 2 calculation questions, with a calculator on the page. Your progress saves in this browser for 24 hours, so you can stop and finish later. Then ask Lug, the AI study assistant, why the answer is right and the others are wrong.
Special Occupancies, Equipment, and Conditions
After normal power fails, within how many seconds must an emergency system make power available to its required loads?
Press A-D or 1-4 to choose an answer while this question is on screen.
Choose an answer to begin
Worked offset: 6 in at 30°
The offset must clear an obstruction that starts 30 in from the end of the conduit.
- Distance between marks: 6 × 2.000 = 12 in.
- Shrink: 6 × 0.268 = 1.61 in, about 1 5/8 in.
- Mark nearest the obstruction: 30 + 1.61 = 31.61 in from the end, about 31 5/8 in. Klein's steps place this mark the same way, adding the total shrink to the distance to the obstruction.
- Other mark: 31.61 − 12 = 19.61 in from the end, about 19 5/8 in.
- Degrees used: 60°.
Worked offset: 4 in at 22.5°
- Distance between marks: 4 × 2.613 = 10.45 in, about 10 7/16 in.
- Shrink: 4 × 0.199 = 0.80 in, about 13/16 in.
- Degrees used: 45°.
With Klein's rounded figures the marks would sit 4 × 2.6 = 10.4 in apart, with 4 × 3/16 = 3/4 in of shrink. Both are within 1/16 in of the exact figures, so at this depth the rounding barely matters.
3-point saddle: exact vs field values
A 3-point saddle crosses a pipe or other obstruction with a 45° center bend and two 22.5° outer bends. Each half is a 22.5° offset with the obstruction's height as its depth. That gives two exact rules, set against the figures in Klein's saddle table:
| Per inch of obstruction height | Exact | Klein field value |
|---|---|---|
| Outer marks from the center mark | 2.613 | 2 1/2 in |
| Center mark moved past the measured center | 0.199 | 3/16 in |
For a 3 in obstruction, the outer marks sit 3 × 2.613 = 7.84 in each side of the center mark, against 7 1/2 in from the field value. The center mark moves 3 × 0.199 = 0.60 in, against 9/16 in. The saddle uses 90° of the run's 360°, and its total shrink is 2 × 0.199 × 3 = 1.19 in.
Klein's table also lists a 60° center with 30° outer bends: 2 in from the center mark and 1/4 in of center-mark shift per inch. The exact values there are the 30° row of the chart, 2.000 and 0.268.
The free conduit bending calculator works offsets at any angle, 3-point and 4-point saddles and 90° stubs, shows the exact and field saddle figures side by side, and keeps a running total of degrees against the 360° limit.
Print the chart
To keep the chart in your bag, print this page or save it as a PDF from your browser's print menu. The site header and footer are left off the printout, so the tables and worked examples print on their own.
Find your weak spot first
Studying for the Texas journeyman exam? Take the free 10-question check to see where you stand across its subject areas before you drill more. It needs no signup and explains every answer.
FAQ
Why is 30 degrees the easy offset angle?
Because sin 30° is exactly 0.5, the multiplier is exactly 2: the marks sit twice the offset depth apart, which you can work in your head. The shrink, 0.268 in per inch, is close to 1/4 in, and the offset uses 60° of the 360° between pull points.
What is shrink in a conduit offset?
Shrink is the run an offset uses up. Once bent, the conduit reaches less far along the run than it did straight. Per inch of offset it is tan(θ ÷ 2), so a 6 in offset at 30° shrinks 6 × 0.268 = 1.61 in. Add it to your measurement to the obstruction before you mark.
How many degrees of bends are allowed between pull points?
360° in total, the same as four 90° bends, between pull points such as boxes and conduit bodies. In the 2014 NEC each raceway article sets the limit in its own section: 358.26 for EMT, 344.26 for rigid metal conduit, 342.26 for IMC and 352.26 for PVC. Look the rule up in the edition your job or exam is under. A 30° offset uses 60° and a 3-point saddle uses 90°.
Sources
- Conduit Bender Guide (PDF), Klein Tools: the offset formula table, the offset marking steps and the 3-point saddle table. Checked 21 Nov 2026.
- NFPA 70, National Electrical Code, 2014 edition, as posted by Public.Resource.Org: 342.26, 344.26, 352.26 and 358.26, section numbers only. Checked 21 Nov 2026.
Bonding Jumper editorial team
Related guides
Free tools for this topic
Keep reading
Your next step
Ready to see where you stand on TX Journeyman?
Free, untimed and scored by domain. No signup. About 14 minutes. Most checks include 2 calculation questions, with a calculator on the page. Your progress saves in this browser for 24 hours, so you can stop and finish later.
Free 10-question checkTexas Journeyman course. Lessons, timed practice exams and a plan around your exam date.
Get Texas Journeyman course · $99More free practice
- Read a free lesson
- Take the free 25-question practice test
- Question of the day
- Free flashcards
- Print a class quiz (free PDF)
- Print the flashcards as cut-out cards (free PDF)
The free check and the course are on the TX Journeyman page.